Z-Fighting - Revision history

Cman2k: image and formatting fixes

2014-11-26T09:15:02Z

image and formatting fixes

Cheeseplus: 2 revisions

2014-07-29T08:46:14Z

2 revisions

EricChadwick: picture, formatting

2011-07-14T00:59:10Z

picture, formatting

EricChadwick: added

2011-07-14T00:53:44Z

added

New page

__NOTOC__
= Z-Fighting =
Also called flickering, duplicate geometry, coplanar meshes, shimmering.

Z-fighting is a term used in 3D games to describe two (or more) polygons which are coplanar, or very close. Tiny rounding errors usually mean that the geometry appears to flicker as pixels from one piece or the other appears seemingly randomly.

In this day and age it's less prevalent due to multistage texturing in shaders but occasionally still rears its ugly head depending on geometry, software or hardware.

A good example would be a billboard on a brick wall - the player can never see behind the billboard but the artist might still be tempted to leave the brick wall there for speed and simply position the billboard quad over the brick wall with a tiny amount offset. Depending on z-buffer setup and the hardware it's running on you might see a strange billboard/brick interference pattern as you move about the scene.

== Solutions ==
Figure out what the minimum distance is for your game, and use that.



Rinse and repeat until you find the minimum safe distance that you can "float" a plane above another surface without flickering/z-fighting. You can then clone this mesh to create all future "floaters" (posters, litter, decals, etc.)

Some game tools will allow you to manually offset the Z-test values that a model will use. So the model can be coplanar with another model, but it is forced to use slightly different depth values when it is rendered.

----
[[Category:Glossary]]

@@ Line 1: / Line 1: @@
-__NOTOC__
+[[image:Z-fighting.png|thumb|Z-fighting between two coplanar models. <BR> Image by [http://en.wikipedia.org/wiki/User:Mhoskins mhoskins] ]]
-= Z-Fighting =
 Also called flickering, duplicate geometry, coplanar meshes, shimmering.
 Z-fighting is a term used in 3D games to describe two (or more) polygons which are coplanar, or very close. Tiny rounding errors usually mean that the geometry appears to flicker as pixels from one piece or the other appears seemingly randomly.
 A good example would be a billboard on a brick wall - the player can never see behind the billboard but the artist might still be tempted to leave the brick wall there for speed and simply position the billboard quad over the brick wall with a tiny amount offset. Depending on z-buffer setup and the hardware it's running on you might see a strange billboard/brick interference pattern as you move about the scene.
-== Solutions ==
+= Solutions =
 Figure out what the minimum distance is for your game:
 # Make a plane primitive and snap it to a large ground model.

← Older revision	Revision as of 08:46, 29 July 2014
(No difference)

@@ Line 5: / Line 5: @@
 Z-fighting is a term used in 3D games to describe two (or more) polygons which are coplanar, or very close. Tiny rounding errors usually mean that the geometry appears to flicker as pixels from one piece or the other appears seemingly randomly.
-In this day and age it's less prevalent due to multistage texturing in shaders but occasionally still rears its ugly head depending on geometry, software or hardware.
+{| border="1" cellpadding="2" cellspacing="0"
 A good example would be a billboard on a brick wall - the player can never see behind the billboard but the artist might still be tempted to leave the brick wall there for speed and simply position the billboard quad over the brick wall with a tiny amount offset. Depending on z-buffer setup and the hardware it's running on you might see a strange billboard/brick interference pattern as you move about the scene.
 == Solutions ==
-Figure out what the minimum distance is for your game, and use that.
+Figure out what the minimum distance is for your game:
-<!-- # Make a plane primitive and snap it to a large ground model.  -->
+# Make a plane primitive and snap it to a large ground model.
-<!-- # Move the pivot slightly below the plane, and re-snap.  -->
+# Move the pivot slightly below the plane, and re-snap.
-<!-- # Export to the game and spin the camera.  -->
+# Export to the game and spin the camera.
-Rinse and repeat until you find the minimum safe distance that you can "float" a plane above another surface without flickering/z-fighting. You can then clone this mesh to create all future "floaters" (posters, litter, decals, etc.)
+# Rinse and repeat until you find the minimum safe distance that you can "float" a plane above another surface without flickering/z-fighting. You can then clone this mesh to create all future "floaters" (posters, litter, decals, etc.)
 Some game tools will allow you to manually offset the Z-test values that a model will use. So the model can be coplanar with another model, but it is forced to use slightly different depth values when it is rendered.